Wet N Gone - Wet N Gone Fusible - Wet N Gone Tacky
This unique product is a fibrous water soluble stabilizer and does a superior job of supporting dense embroidery designs. Embroider most free standing lace with just one layer! Its clean rinse capability makes it the best choice when using it with delicate fibers such as yarn scarves or English netting. It is now available in a fusible as well as a sticky version.
*Use the fusible
version on sheer fabrics such as organdy, organza, lame, sheer silks and more to establish a solid type fabric that is easier to hoop and embroider. Once the embroidery is complete, all the stabilizer rinses away and will not shadow through.
*Use the sticky or tacky
version of Wet N GoneÂ® to embroider delicate designs on hard to hoop items such as the corners of handkerchiefs, silk blouse collars and more. Particularities:
- Create freestanding lace and use just one layer for most designs
- Perfect for making appliquÃ©s, decorative pins and/or 3-D embroidery.
- Rinses clean leaving no messy residue
- Use as a topping for wide satin stitch designs on high pile fabrics for perfect results!How to use regular Wet N GoneÂ® for free standing lace and/or embroideries:
1. Hoop one layer of the stabilizer within the embroider frame. Try to achieve "tight as a drum" tension without stretching or distorting the stabilizer.
2. Embroider the design.
3. Remove the product from the hoop and trim away as much of the stabilizer as possible.
4. Rinse away the Wet N GoneÂ® using luke warm water. *Tip
: If your desire is to have the lace stiff, simply get the embroidery wet. Don't rinse! Once it is wet, the stabilizer will be absorbed into the stitching and will dry stiff.How to use Wet N Gone FusibleÂ®:
1. Fuse one layer of the stabilizer on to the back of the fabric. Be sure to use a piece at least one inch larger than the outer parameter of the hoop to insure proper stabilization. *Important
: Use a low temp (260Â°, silk) setting on your iron. Do not touch the surface of your iron to the Wet N Gone FusibleÂ®, use a press cloth (muslin or cotton). Press quickly! It is not necessary to hold the iron to the fabric for more than three seconds.
Repeat steps 2-4 from above.How to use Wet N Gone TackyÂ®:
1. Place one layer of the product in your embroidery hoop, paper side up.
2. Score the release paper with a pin or needle and peel back.
3. Stick the garment or item to be embroidered in place and smooth out any wrinkles.*Tip
: It is necessary to use "soft" water to get optimal rinse results with this product.
Repeat steps 2 - 4 from above.Free Scarf Project:http://www.rnkdistributing.com/yarnscarf.shtmlWhere to buy:
Floriani's Wet N GoneÂ®http://www.myembroideryhaven.com/shop/i ... h=21_36_46
Floriani's Wet N Gone FusibleÂ®http://www.myembroideryhaven.com/shop/i ... h=21_36_47
Floriani's Wet N Gone TackyÂ®http://www.myembroideryhaven.com/shop/i ... h=21_36_48Marie's Comment:
Keep all your remnants of these products. There are tons of ways you can reuse them. You can use them to stiffen items. You can use the remnants to do repairs on items that normally you would have a hard time repairing with your machine because the item would
ch in the feed dogs. Simply slip a piece under your item and you can do the repairs with your machine. Use remnants of the Tacky version to assemble delicate items together with your machine instead of having to pin or assemble by hand.
Click Here for a Tutorial on using your stabilizer remnants to machine assemble items that we normally assemble by hand:http://www.myembroideryhaven.com/tutori ... icates.zip